27/05/2022
If you ignore waterproofing,
This project not only harms you,
also hurt the neighbors
These detailed steps for preparing waterproofing at home must be collected.
The first step is to clean up the base layer, and clean up the floating ash on the ground and walls.
The second step is to sprinkle water to completely wet the ground to ensure that the base layer is wet.
The third step, leveling with cement mortar, water and electricity slots and wall grooves.
The fourth step is to make a water stop table with cement mortar to prevent the water from stealing the base layer in the later stage, to ensure that it is smooth and free of floating ash, and it is convenient for later painting.
The fifth step is to level the surface with lime as a whole, and turn it outwards by 30 cm to prevent the ground from being uneven in the later stage.
The sixth step is to carry out the groove treatment of the pipe root, and brush the horns around the pipe to block the leakage net.
The seventh step is to stir the paint evenly according to the ratio. Wake up for fifteen minutes.
The eighth step is to reinforce the pipe root and the yin and yang corners with waterproof paint again.
The ninth step is to wet the painted wall with a watering can, so that the waterproof coating can be better combined with the wall.
The tenth step, the ground is brushed with flexible waterproof,
It can ensure better tensile strength and elasticity.
Wall brushed rigid waterproof,
Prevent the tiles from falling off later.
The shower area petitioned 1.8 meters,
Petition at the door for fifty centimeters,
Thirty centimeters for foreign visits,
To prevent the wall from peeling off later.
The eleventh step, brush the second coat of waterproof coating to ensure that the thickness of the waterproof layer is uniform.
The twelfth step, the ground is protected by polypropylene cloth.
To prevent the latter from being damaged by the next process.
The thirteenth step, stir the waterproof mortar evenly, pour it under the polypropylene cloth and brush it evenly, then cover it with polypropylene cloth, use a brush to drive out the air bubbles, and also brush the small pieces of polypropylene cloth with the waterproof mortar cover on the tube,
compact it with a brush,
completely exhaust the air inside,
Ten centimeters are scattered on the wall.
Finally, after waiting for 24 hours, do the closed water experiment,
The waterproofing made in this way no longer has to worry about the house leaking.
如果你忽略了防水，
这项工程不仅害了你自己，
也害了邻居
家里准备做防水的这些细节步骤一定收藏好了。
第一步，基层清理，把地面跟墙面的浮灰清理干净。
第二步，洒水，把地面全湿，保证基层湿。
第三步，用水泥砂浆找平，水电开槽和墙槽处。
第四步，用水泥砂浆制作止水台，以防后期水漫盗走了基层，保证平整无浮灰，方便后期涂刷涂料。
第五步，用石灰整体抹面找平，外翻三十公分，以防后期地面不平整。
第六步，进行管根开槽处理，将管子周围耕耘羊角刷涂一遍，堵漏网。
第七步，按照配比对涂料进行搅拌均匀。醒廖十五分钟。
第八步，再次用防水涂料对管根处与阴阳角处进行加固处理。
第九步，对涂刷墙面用喷壶进行湿润处理，使防水涂料能与墙面更好的结合。
第十步，地面刷涂柔性防水，
能保证更好的拉伸强度弹性。
墙面刷涂刚性防水，
防止后期瓷砖脱落。
淋浴区上访一点八米，
门口上访五十厘米，
外访三十厘米，
以防后期墙面起皮缓解。
第十一步，刷涂第二遍防水涂料，保证防水层面厚度均匀。
第十二步，地面用丙纶布做丙纶保护，
防止后期被下一道工序破坏。
第十三步，把防水砂浆搅拌均匀，倒入丙纶布下面用毛刷刷均匀，再用丙纶布盖起来，用毛刷把气泡赶出去，把小块的丙纶布也要刷满防水砂浆套在管子上，
用刷子给它压实，
把里面的空气完全排出，
墙面散放十公分。
最后等待二十四小时后做闭水实验，
这样做出来的防水再也不用担心房子漏水了。
预知更多详情可联系：
MR.AML
011-70718928
WhatsApp Link
https://wa.link/24buyt
如果你忽略了防水，
这项工程不仅害了你自己，
也害了邻居
