Apex Motorsport NZ

Apex Motorsport NZ New Zealand based Motorsport company who specialises in all things Rotary and Fabrication

FD rx7 side hussle finished up, this one i bought off a customer with a blown engine, rebuilt motor new rotor housing an...
11/08/2026

FD rx7 side hussle finished up, this one i bought off a customer with a blown engine, rebuilt motor new rotor housing and consumables, binned the sub standard single turbo setup in favour for a G35 1050 turbo , made all new 3.5” stainless exhaust and cooler piping, installed Link G4x plug in with multiple sensors , New fuel system , NDT Developments on the tuning, Off to its new home next week 🙌

Little side project ive taken on, FD rx7 with a blown motor, One of the previous owners decided to single turbo a stock ...
21/07/2026

Little side project ive taken on, FD rx7 with a blown motor, One of the previous owners decided to single turbo a stock ecu and fuel system, didnt take long for the front apex seal to leave the chat

Ive stripped the FD motor, Found that the engine had done less than 5000kms with all new parts , Had to Replace the front rotor housing , seals, springs and consumables. While in there stage 2 main ports and exhaust, Fitted a 400kw capable single plate clutch.

Upgraded Injectors, rails and fuel pump. Replaced stock ecu with Link G4x plug in, added boost control, safety sensors and 3bar map sensor.

The Single turbo setup was replaced with a Sinco divided exhaust manifold , PSR G35 1050 turbo and 50mm wastegate, i will replace the front half of the mild steel exhaust with 3.5” stainless to match rear half

Hoping to have on dyno before chrome and will be listed for sale afterwards, for more info PM me

Jasons brand new FD engine going back into vehicle today, Unfortunately None of the previous engine was salvageable and ...
12/07/2026

Jasons brand new FD engine going back into vehicle today, Unfortunately None of the previous engine was salvageable and we had to start again with mazda crate engine

Stripped, painted , ported to secondary bridgeport, race seals and reassembled.

Thanks Jason for trusting me with your build, more updates to come as we update lots of old tech on this car and get it to NDT for tune

Julians infamous RX3 on the dyno today at NDT Developments , quite a few changes over previous setup, Now featuring a Br...
18/06/2026

Julians infamous RX3 on the dyno today at NDT Developments , quite a few changes over previous setup, Now featuring a Bridgeport engine ( Previously stage2 ) , PWR intercooler ( Previously GTIR Nissan ) , Green brothers radiator and spal fan ( Previously Chinese and viscose fan ) , Borgwarners latest SXR368 turbo ( previously SXE366 ) , New engine harness with additional safetys , and finally water/meth ( Purely for burnout comps where intake temps saw 150deg )

Just low boost tune for now 15psi, as we put some kms on it before we push 20psi and let the new turbo stretch its legs

Thanks Julian for your patience and support 🙏

13b REW engine completed for a RX8, originally built 10years ago now with modern tech, Rebuilt engine inc near new housi...
02/06/2026

13b REW engine completed for a RX8, originally built 10years ago now with modern tech, Rebuilt engine inc near new housings and rotating assembly, updated porting. Link ecu with safetys , Rebuilt turbo and updated fuel system.

13/05/2026

Nathans B1600 ute i had the pleasure of helping Nathan with , tasked with building a 13b bridgeport package Nathan then mounted into the vehicle, We then made a equal length exhaust and installed driveshaft hoops and a bunch of other small tasks. Now fully legal and tuned you will see this one around at all the car meets in Auckland

Thanks again Nathan for always trusting me with your builds

Thanks Mark at Revolution engine services for sorting tune on this

Custom exhaust manifold for Jons 323 all wrapped up, Borgwarner S366 and Turbosmart 50mm progate taking care of buisness...
12/05/2026

Custom exhaust manifold for Jons 323 all wrapped up, Borgwarner S366 and Turbosmart 50mm progate taking care of buisness,

Julians 13b bridgeport turbo motor finished up, Secondary bridge, stage center, Complete S6 engine , Timeless vapour bla...
15/03/2026

Julians 13b bridgeport turbo motor finished up, Secondary bridge, stage center, Complete S6 engine , Timeless vapour blasted housings with Gloss black plates.

Trents S6 13b semi pp NA engine all wrapped up, Brand new S5 housings, S6 balanced rotating assembly, 25mm Semi pp , Sta...
13/03/2026

Trents S6 13b semi pp NA engine all wrapped up, Brand new S5 housings, S6 balanced rotating assembly, 25mm Semi pp , Stage 2 main ports, Exhaust porting

Vapour blasted by Trent, looks incredible

Thanks Trent for your patience on this one as we catch up on engine builds

Another day another dyno tune ahead of Rotary Reunion, quick health check with NDT DevelopmentsNew shop FD track car for...
05/02/2026

Another day another dyno tune ahead of Rotary Reunion, quick health check with NDT Developments

New shop FD track car for a quick sq**rt to make sure we can full send at RE , stock port , T3 61mm masterpower holding the combo back from stretching its legs, No doubt this combo will be coming out and getting the Full apex make over in the coming months, for now should be a bit of fun

Address

Whangaparaoa

Telephone

+642102526684

Website

Alerts

Be the first to know and let us send you an email when Apex Motorsport NZ posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category