06/12/2026
Unreal RC
Scroll down for scx 30 rules
Any rock crawler brand allowed as long as they are 1/18 scale 1/24 scale
Kids class will be for ages 0-12
Class 1
Body
Bodies may be constructed of any material (lexan, ABS,
3d printed, etc.). The width of the body at the doors of
the cab must be wider than the inside edge of all four
tires. Bottom edge of front grill and rear tailgate/trunk
must be below the top edge of all four tires when the
vehicle is at rest on flat ground. Bottom edge of bodies
must be at a height where the transmission is not seen
when viewed from the side. Front and rear of body
must extend past the front edge of the front tires and
rear edge of the rear tires. This may be accomplished
with chassis mounted bumpers if the body itself does
not meet requirements. Lexan bodies must have a front
windshield and rear window. Bodies with roll cages
instead of cabs (such as the Axial Deadbolt) do not need
to have windshields or rear windows.
Chassis
Must use a chassis that consists of two vertical rails or
bars in similar configuration as stock chassis. Rails may
be carbon, aluminum, titanium, 3d printed, etc. No tube
chassis or stick style chassis. Chassis must use a 0 degree
skid plate. No angled skid plates. Chassis rails must
extend past the centerline of both front and rear axles.
Bumper
All vehicles must run a front bumper that is wider than
the widest part of the frame rails. Bumper must extend
past the front edge of the front tires and mounted in such a way that the lower edge of the bumper is no higher
than the lower edge of the front of the body. Lights not
required.
Motor
Brushed or brushless motors allowed. Single motors only.
Battery
Any lipo battery up to 3s. Battery may be relocated but
must be attached to chassis and must stay under the
body.
Electronics
No electronics limitations.
Wheels
Any wheel with maximum diameter of 1.0”. One piece
wheels or beadlocks allowed.
Tires
Any tire with 57mm maximum outside diameter. Tires
must be constructed of a single piece of rubber as
originally manufactured. Tires must retain stock markings
on sidewall including brand, model, size, etc. Tire tread
may be trimmed/removed. Tires may be vented.
Drivetrain
Full time 4WD only. No 6x6 or dually setups. Front
wheel steering only. Vehicles with 4 wheel steering may
compete in this class as long as rear steer is not used
during the run. Use of rear steer will be considered a
disqualification.
Suspension
Aftermarket shocks allowed. Must use 4 shocks - 1 per
tire. Suspension links may be changed.
Gate size 6.5"
Class 2 1/24 Mod
No 4 wheel steer
No cage chassis
No dig setup
Chassis must be longer then wheelbase
Half cab must have rear bed or cage
Must have Lexan or Hardbody 1/24 model or bigger. No team associated 1/28 bodies
Max wheel size 1.0
Max tire size 57mm
Gate 6.5"
Class 3 1/24 Outlaw
Dig chassis allowed (can not have 4 wheel steering)
4 wheel steering allowed (cant have dig function)
All cage chassis except Meus racing ripper / Little guy racing ripper / Micro shark / Injora plastic chassis Buggy
No In or max wheel size
No tire size limit
Winch allowed
Gate 7.0"
Class 4 1/24 Hardbody
No 4 wheel steer
No dig
No cage chassis
Chassis must be longer then the wheelbase
Wheel size 1.0
Maximum tire size 57mm
Hard plastic body, 3d printed, or Die cast body 1/20-1/25 scale
Half cab must have rear bed or cage
No comp style cuts on body
Winch allowed Gate 6.5"
Class 5 1/24 Buggy
All ripper style, Micro shark, Injora buggy, and ultra 24 style chassis
No 4 wheel steer
No dig allowed
Winch allowed
Max tire size 57mm
Max wheel size 1.0
Gate 7.0"
Class 6 - 1/18 Stock
Stock style frame rails can be steel, carbon, aluminum or titanium
Tire size 62mm and below
Wheel size 1.0
Stock body
Stock bumpers
No 4 wheel steering, No 6x6, front wheel steer only or rear steer locked out.
No Capra 1/18
Battery 3s max mounted under the body
Shocks no limit in size. 1 per corner
Gate 7.0"
Class 7 1/18 Modified
Tire size any allowed
Wheel size any allowed
Any chassis allowed
Gate 7.0"
Body All allowed
No bumpers and bumpers allowed
6x6 4ws allowed
Any Battery size allowed
No shock limit per corner or length
No Capra 1/18
Gate size 7.0"
Everything is allowed that is excluded from class1 rules!
Happy Crawling!!
Scx 30 rules
class 1 box stock.
Vehicle must be box stock, No aftermarket upgrades allowed. Parts may be swapped out from other scx30, example K10 wheels and tires on Wrangler
class 2,
any aftermarket upgrades allowed, must run stock chassis
class 3
any and all modifications will be allowed.
