FPK Precision, LLC

17/09/2020

15/04/2020

Almost there...

It troubled us deeply for the past few weeks to have orders older than a week unshipped, but we have finally dug out. This means that starting next week, we will be back to shipping order within 1-2 days. You can now order with confidence!

https://www.brazosprecision.com/

We have been working non-stop for the past few weeks to hire, train and adopt a much expanded production schedule. We now have eight (8) times the casting capacity available than just a month ago and are just about caught up on all backlogged orders.

What this also means is we now have capacity to take on commercial reloaders who are having trouble getting bullets from their traditional suppliers. We have lead, we have the product capacity, and we are happy to get you what you need to service your customers. Please reach out to us messaging this page, calling us, or emailing [email protected]. Let's get the public the ammo that they are demanding!

Just a few orders are still old due to the last 1-2 profiles we are catching up on and resizing requests that have been difficult to get done with the sizers running non-stop of primary production. Even these will be out by end of this week.

28/03/2020

28/03/2020

We are shipping every day USPS will pick up!

Shipping is continuing on Saturdays now that we can have USPS picking up six days a week. We are working hard to get the last the the orders that are older than a week packed and out today, and are adjusting so we can get back to shipping everything in a couple of days.

Get yours at: www.brazosprecision.com

Thank you everyone for understanding, while we adjust to the new volume of orders, and especially thank you to all of the new customers!

Finally, thank you to our team for rallying around and getting all of this extra production running. We could not do it without all of you! Not everyone is on FB, but thank you Ash Fisher, Zeric Hallford, Robert Davis, Mason Talbert, Jacob Lustick, Garrett Husky, and Zach Brown.

18/03/2020

We are up and running with loaded ammo using Brazos Bullet Company bullets in 45 ACP, and hope to have website ordering online soon. We are focusing on competition loading, so you can specify a powder charge or velocity and we will load them to spec. All rounds are case gauged.

At this point we are providing pickup at our College Station location, or deliver to one of the following matches:
- Dallas Piston Club, 1st Sunday
- Terrell Bullseye, 2nd Sunday
- Austin Bullseye, 3rd Sunday
- Houston Bullseye, 4th Sunday

Reloaded cases we supply cases, and exchange case prices require you to provide replacement cases at the time of delivery.

Subscription pricing is available if you order more than two cases in in 3 months, or 4 in 6 months.

13/03/2020

Reaming slide stop holes to 0.2031

If you have an otherwise reasonable barrel, that just doesn't have enough lower lug engagement when in lock-up, an inexpensive fix is to replace the slide stop pin with an oversized one from EGW Inc. You can see the solid contact on both lugs with the new slide stop pin in place after reaming the hole to fit. Prior to this there was almost no contact on the standard pin, which measured 0.1995.

The oversized pins come in 0.2030. Usually, the pin hole is 0.202 or just under, so you only need to ream out 0.001. I use a 0.2031 carbide reamer that leaves a hole where the EGW slide stop pin goes in cleanly with no play over the free rotation needed. Overall a $75 fix instead of a $300 new barrel fitting.

22/02/2020

New brass wash mixer setup

Brass cleaning mixer with a steel ring with a screen that will allow water, pins and media to pass, but not cases. This will sit upright to wash and polish and then be tilted downward to drain out water, pins and media. Simple, elegant and contained.

22/02/2020

A box full of 1911 triggers for builds!

19/02/2020

New summer project just in the shop!

This summer when it becomes July, I am going to get my class II SOT, so that I can manufacture and handle NFA items. At that time I am going to make some integrally suppressed 22s out of these R***r Mark IV receivers. Should be a good project and give me something special that I can offer out of the manufacturing part of the business!

The first picture are the five (5) receivers I purchased for the projects and the second is of version of the result that I am going to be producing. Should be good fun!

10/02/2020

Impressive fixture (and packaging)!

Got my 1911 fixture from Doty Manufacturing, Inc. Really solid piece of kit, so that I can now work consistently in mostly just a few fixtures instead of ad-hoc setups. Looking forward to getting this into the shop!